Car Key Button Repair
A broken car key button can be a source of frustration. It is possible to call an emergency locksmith service or purchase an alternative remote.
However, you might be saving money by repairing an old key fob instead of replacing it. This is especially true if an old switch or damaged contacts are at the root of the issue.
car key repairs near me
If the buttons on your key fob don't respond to pressing it, it could be an obvious indication that your battery is dead or nearing the end of its lifespan. Fortunately, replacing the battery is a simple task that can be completed on your own rather than hiring a locksmith or dealer to complete the task for you.
Find the battery compartment first. It is usually located on the backside of the key fob. It may be hidden behind a slide-out cover or an access point that opens when you press a button. When the compartment is opened then look for the small button-cell battery. It is usually shaped like an oblong coin and is marked with the plus and minus signs. Remove car key repairs , and replace it with a new one. Make sure that the plus and minus symbols are aligned correctly.
Once the battery is in place Close the compartment and snap the two parts of the key fob. Make sure to align the parts and snap them in place properly before closing the door and testing your keys. Press any of the buttons to confirm that they function correctly.
If the remote key fob you have purchased stops working even after you replace the battery, it may be experiencing other issues that require a different type of repair. Dropping the device in a puddle could cause it to stop functioning. Or, it could be experiencing an internal electrical problem or may need to be deprogrammed by an expert or locksmith. Find out what's wrong related to your key fob using these other car troubleshooting techniques.
Switches
Depending on the year and the manufacturer, there are various kinds of switches that are found in the keyfob of your car. The older style keys have a chip that is visible inside the case. The newer keys work by transmitting signals to your car. The buttons on a key can be damaged or worn out by normal use, regardless of the type. The result is they become difficult to press, or even ineffective. If you force the button it can cause further damage. It may also prevent the key from functioning in the future.
If your key doesn't seem to be working, you should first try changing the battery. If this doesn't work, you might need to clean your key fob or adjust its switches. Since these tiny electronic switches spend a lot of time being tossed around they are more prone to break down than the larger parts of your key.
The switches are rubber-like and are coated with an electricity conducting film that is prone to wear out over time. However, they're a very small part and cheap to replace. The old ones are soldered to the circuit board, so you'll have to take care to remove them without causing damage to other parts. Then you can put in the new ones and rebuild your key fob.
One way to prevent your car key fob from getting damaged is to avoid using it for more than a few hours at a time and to keep it out of the way in visible locations that it will be visible. Also, you should find a secure place to store your key when you're not making use of it.
If the issue persists after you've cleaned your key fob, replaced the battery and tried to clean it, then you might need to contact a locksmith. A professional can test the frequency of your key to see whether it's still able communicate with your vehicle, and open and replace micro switches, swap cases, and more.
Outer Case
If the buttons can't move freely in the case, they could get stuck or break. If changing the battery or cleaning with the help of a cotton swab or rubbing alcohol doesn't fix the issue, then removing the case and checking it out might be necessary. If the contacts the buttons touch aren't an ideal fit or are worn, changing them might be the only solution.
Rubber buttons be worn out over time. Rubber buttons can become difficult to press when they stretch, and nails may scratch them. In this scenario, the key may fail, and it's time to replace the case or the buttons. This repair involves disassembling your remote, locating the button switches on the board, then heating the solder and carefully removing them. The circuit board then gets soldered with new buttons. The case is then rebuilt with the horse shoe key blade piece inserted. The new buttons must be snugly fitted inside the case to stop them from falling out.
Inner Case
Since your key fob is prone to get jostled around and may sometimes be accidentally pressed, the buttons inside can be damaged or stuck over time. If your key fob ceases to function while you are away from home, you can fix the problem quickly by using metallic tape and punch holes. This will allow you to unlock doors, but not start the vehicle. This simple fix can enable you to safely get back to your car and complete your journey.
